All of these parts are from Kit Plate of iGEM foundation.
The lock3 can inhibit the expression of the later ptet.When key3d bind to the lock3,the inhibiting effect will be removed and the level of expression of GFP will increase.
This is a composite part including taRNA (key3d), crRNA (lock3) and GFP.
RBS (Elowitz 1999) -- defines RBS efficiency
Varies from -6 to +1 region from original sequence to accomodate BioBricks suffix. No secondary structures are formed in the given RBS region. Users should check for secondary structures induced in the RBS by upstream and downstream elements in the +50 to -50 region, as such structures will greatly affect the strength of the RBS. Contact info for this part: Brian Chow
Vinay S Mahajan, Voichita D. Marinescu, Brian Chow, Alexander D Wissner-Gross and Peter Carr IAP, 2003.
Lutz, R., Bujard, H., Nucleic Acids Research (1997) 25, 1203-1210.
Sequence for pTet inverting regulator driven by the TetR protein.
BBa_R0040 TetR-Regulated Promoter is based on a cI promoter. It has been modified to include two TetR binding sites and the BioBrick standard assembly head and tail restriction sites.
June Rhee, Connie Tao, Ty Thomson, Louis Waldman
[key3c] riboregulator for lock3 variants
This part has the same homology region to J01122 as J23007 except that unlike J23007, J23008 does not contain the hairpin that was derived from J01129. J23008 anneals linearly to the stem of the hairpin in J01122 with perfect base pairing and destroys the hairpin in the process and reveals the RBS on J01122. When J01122 is transcribed the RNA secondary structure is such that the RBS hairpins with sequence upstream preventing the ribosome from binding and translation from occuring thereby locking up RFP further down stream. When J23008 is introduced into the cell in trans, we suspect that it will unlock the RBS for RFP as described above allowing translation to occur.
[key3d] riboregulator for lock3 variants
Variant of key3 (see part J01129 (key3), J23007(key3b), J23008(key3c)). Part is in pJ23006, so there is a Ptet upstream of the XbaI site to drive expression. Nevertheless, J23009 is still a basic part allowing both prefix and suffix insertions.
Derived from the TE terminator of T7 bacteriophage between Genes 1.3 and 1.4 <genbank>V01146</genbank>.
Transcription terminator for the E.coli RNA polymerase.
Suggested by Sri Kosuri and Drew Endy as a high efficiency terminator. The 5' end cutoff was placed immediately after the TAA stop codon and the 3' end cutoff was placed just prior to the RBS of Gene 1.4 (before AAGGAG). Use anywhere transcription should be stopped when the gene of interest is upstream of this terminator.
Transcriptional terminator consisting of a 64 bp stem-loop.
RBS.1 (strong) -- modified from R. Weiss
Strong RBS based on Ron Weiss thesis. Strength is considered relative to <bb_part>BBa_B0031</bb_part>, <bb_part>BBa_B0032</bb_part>, <bb_part>BBa_B0033</bb_part>.
Varies from -6 to +1 region from original sequence to accomodate BioBricks suffix ("orig" in figure 4-14 of Ron Weiss thesis). No secondary structures are formed in the given RBS region. Users should check for secondary structures induced in the RBS by upstream and downstream elements in the +50 to -50 region, as such structures will greatly affect the strength of the RBS. Contact info Brian Chow
green fluorescent protein derived from jellyfish Aequeora victoria wild-type GFP (SwissProt: P42212
GFP (mut3b) [note that this part does not have a barcode]
Conversion of the iGEM parts registry to SBOL2.1